Wainscoting Calculator

Enter a wall's length, the panelling height, the stile and rail widths and the largest panel you want, and get the picture-frame panels, their clear width and the frame boards to buy, wall by wall.

Estimates for planning, not professional advice. Read the full notice.

Wall and frame

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 3.6 metres, 11 feet 9 and 3 quarters inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 900 millimetres, 2 feet 11 and 7 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 80 millimetres, 3 and 1 eighth inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 140 millimetres, 5 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 90 millimetres, 3 and 9 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 600 millimetres, 1 foot 11 and 5 eighths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 2.4 metres, 7 feet 10 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Example: a wall with picture-frame panelling

6 frame boards

  • Panels 6 panels
  • Stiles 7 stiles
  • Clear width of each panel 0.507 m (1.662 ft)

Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.

  • Frame boards (stiles and panel rails), frame boards, 2.4 m 6
  • Base rail boards, base rail boards, 2.4 m 2
  • Cap rail boards, cap rail boards, 2.4 m 2

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    How do I work out wall panelling panels?

    Lay a stile at each end and between the panels, so the stiles are one more than the panels. The calculator finds the fewest panels whose clear width stays under your largest panel and shows that width.

    How is this different from board and batten?

    Board and batten gives batten marks across a wall. This page lays out panels between stiles and counts frame parts.

    Worked example: a wall with picture-frame panelling

    Show the steps
    1. Width the stiles take: one more stile than panels 7 stiles × 80 mm (3 1/8 in) = 560 mm (1 ft 10 1/16 in)
    2. Wall left for panels 3.6 m (11 ft 9 3/4 in) − 560 mm (1 ft 10 1/16 in) = 3.04 m (9 ft 11 11/16 in)
    3. Clear width of each panel 3.04 m (9 ft 11 11/16 in) ÷ 6 panels = 0.507 m (1.662 ft)
    4. Frame boards from stock: stiles and panel rails, rounded up once per piece length 7 stiles = 6 frame boards

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes
    Stile width 80 mm (3 1/8 in, converted)
    Default A typed example, not a maker's figure. Check the maker's sheet or your supplier and type your own.
    Largest panel width 600 mm (1 ft 11 5/8 in, converted)
    Default A typed example, not a maker's figure. Check the maker's sheet or your supplier and type your own.

    Panelling and trim board stock, by maker

    Rows: 2

    The nominal sizes and the lengths each maker prints for its panelling and boards, as printed

    The nominal sizes and the lengths each maker prints for its panelling and boards, as printed
    ProductNominal size, inches (thickness by width)Length, feet
    Canfor Appearance Boards (Engelmann Spruce & Lodgepole Pine; trim and fine woodworking) 1x3 – 126 – 16
    Canfor WynnWood Paneling (tongue and groove, Premier / Classic) 1x4 – 86 – 16

    Figures in the Nominal size, inches (thickness by width) and Length, feet columns are per Canfor's product page, checked 15 Nov 2026.

    Product names are trademarks of their owners. HoneyDoMath is not affiliated with, sponsored by or endorsed by these makers. Figures come from each maker's published sheets and are shown for information only.

    Sources: [1][2]

    Canfor prints each size and length as a range; they are shown as printed, not worked out for your wall.

    Sources (2)

    1. Appearance Boards (Canfor product page) (opens in new tab), Canfor, Product page, undated. Manufacturer data.
      “Nominal Dimensions TxW, inches 1x3 – 12 Lengths Feet 6 – 16”
      Per Canfor's product page, checked 15 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 1)
    2. WynnWood Paneling (Canfor product page) (opens in new tab), Canfor, Product page, undated. Manufacturer data.
      “Nominal Dimensions TxW, inches 1x4 – 8 Lengths Feet 6 – 16”
      “2x6 Tongue & Groove ... Nominal Dimensions Inches 2x6 Lengths Feet 12 – 20”
      Per Canfor's product page, checked 15 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 2)

    These are summaries of what the sources say, not professional advice. Building codes and product data change. Check with your local building department and the product label about your own project.