Baseboard Calculator
HoneyDoMath.com
Enter a room's length and width, its doors and the length of your pieces to get the metres of baseboard and the lengths to buy, counted along the run and wall by wall, rounded up once.
Estimates for planning, not professional advice. Read the full notice.
Example: a bedroom
8 lengths of baseboard
- Run around the room 15.6 m (51 ft 2 3/16 in)
- Door width taken off 800 mm (2 ft 7 1/2 in)
- Run to cover 14.8 m (48 ft 6 11/16 in)
- Pieces by the linear count 7 pieces
- Pieces wall by wall 8 pieces
Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.
Result
Enter a size to see your total.
Each product is rounded up once for the whole project, so the total can be less than the items bought alone added together. A line counted from a cut layout (sheets, boards or tiles laid out piece by piece) is counted for each item and added.
- Baseboard, by the length, lengths of baseboard 8
Questions
How many lengths of baseboard do I need?
The calculator takes the doors off the walls, adds your waste allowance once and divides by the piece length. It also counts each wall on its own, because a leftover piece cannot turn a corner, and it buys the larger of the two counts.
Does this work for a whole house or a single room?
It counts one room at a time. Add each room as its own item and the shopping list adds the lengths.
Worked example: a bedroom
Show the steps
- Run around the room: all four walls 4.2 m (13 ft 9 3/8 in) × 2 + 3.6 m (11 ft 9 3/4 in) × 2 = 15.6 m (51 ft 2 3/16 in)
- Take the door off 15.6 m (51 ft 2 3/16 in) − 800 mm (2 ft 7 1/2 in) = 14.8 m (48 ft 6 11/16 in)
- Add the waste allowance, once 14.8 m (48 ft 6 11/16 in) × 1.1 = 16.28 m (53 ft 4 15/16 in)
- Divide by the piece length, round up once; buy the larger of this and the wall by wall count 16.28 m (53 ft 4 15/16 in) ÷ 2.4 m (7 ft 10 1/2 in) = 8 lengths of baseboard
Assumptions
The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.
| Assumption | Value | Details and changes |
|---|---|---|
| Waste allowance | 10% | |
| Default A typical allowance for a straight layout, added once. It is your own figure: change it for your layout. | ||
| Length of a piece | No default | |
| Default The lengths you can buy. Check your label or supplier. | ||
| Width of each door | No default | |
| Default From your own doors. Check your label or supplier. | ||
Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm
Appearance boards Canfor lists
Rows: 1
The nominal size and the lengths Canfor prints for its appearance boards
| Product | Nominal sizes, thickness by width | Lengths |
|---|---|---|
| Canfor Appearance Boards (Engelmann Spruce & Lodgepole Pine; trim and fine woodworking) | 1x3 – 12 | 6 – 16 |
Figures in the Nominal sizes, thickness by width and Lengths columns are per Canfor's product page, checked 15 Nov 2026.
Product names are trademarks of their owners. HoneyDoMath is not affiliated with, sponsored by or endorsed by these makers. Figures come from each maker's published sheets and are shown for information only.
Source: [1]
Canfor prints the nominal size in inches and the lengths in feet; both are shown as printed. The calculator counts pieces from the piece length you choose and does not use them.
Sources (1)
-
Appearance Boards (Canfor product page) (opens in new tab), Canfor, Product page, undated.
Manufacturer data.
“Nominal Dimensions TxW, inches 1x3 – 12 Lengths Feet 6 – 16”
Per Canfor's product page, checked 15 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 1)
These are summaries of what the sources say, not professional advice. Building codes and product data change. Check with your local building department and the product label about your own project.
Sources
- [1] Canfor, Appearance Boards (Canfor product page). Checked 15 November 2026. https://www.canfor.com/products/interior-finishes/appearance-boards