Soil Calculator
HoneyDoMath.com
Enter the length, width and depth of the area to fill or dig and an allowance if you want one, and get the soil in cubic metres, with every step of the math shown.
Estimates for planning, not professional advice. Read the full notice.
The drawing did not open. Length and width are still here.
Area: shape and size
Skip the drawingDrag a round corner to move it. The small hollow diamond on a side is its curve handle: drag it across the side to curve the side (it is not a corner). To add a corner (a new point), tap the side itself, then choose Add a point here. Tapping a corner or a side opens its actions. Drag empty space to move the view; pinch, or Ctrl and the mouse wheel, to zoom. The keys are listed under Keys.
Keys
- Tab
- next corner; each says how far it is from corner 1
- Arrow keys on a corner
- move it one square; ten with Shift; 1 mm with Alt
- Delete or Backspace
- remove the corner; its two sides join in one straight side
- + on a corner
- add a corner halfway along the next side
- Arrow keys on the drawing
- move the view; farther with Shift
- + and - on the drawing
- zoom in and out
- 0 on the drawing
- show the whole shape
- Ctrl+Z (Cmd+Z on a Mac)
- undo, except inside a typed field (it keeps its own)
- Ctrl+Shift+Z or Ctrl+Y
- redo
- Escape while dragging
- put it back where it was
- Enter on a corner or side
- go to its actions
- Escape in the actions
- close them and go back to the drawing
The drawing did not load. Check your connection and try again.
- Area
- 15 m² (161.46 ft²)
- Perimeter
- 16 m (52 ft 5 15/16 in)
- Cut-out edges
No area until the shape is fixed.
Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.
Shape: Rectangle Change
Sides
Corners
Cut-outs
Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm
Example: a low spot
4.5 m³ (5.89 yd³) to order (4.5 m³ exact)
- Volume in place, compacted 4.5 m³ (158.92 ft³)
- The same volume in litres 4,500 L
- Cubic metres at the supplier's smallest order 4.5 m³ (158.92 ft³)
Result
Enter a size to see your total.
Each product is rounded up once for the whole project, so the total can be less than the items bought alone added together. A line counted from a cut layout (sheets, boards or tiles laid out piece by piece) is counted for each item and added.
- Soil, 1 m³ (1.31 yd³) 4.5 m³ (5.89 yd³)
Questions
How do I work out how much soil I need?
Multiply the length and width in metres to get the area, then multiply by the depth in metres. A depth in millimetres is changed to metres first. The result is in cubic metres, and the calculator shows the same volume in litres.
What does the allowance do?
The allowance is a percentage added to the in-place volume to give the loose volume to bring in. It starts at nothing, and the figure is yours to enter.
How much soil does a trench produce?
Enter the trench's length, width and depth. The result is the volume dug out, in place, which is the volume to move or to refill; add an allowance if you want the loose volume.
How many litres are in a cubic metre?
The math above multiplies the cubic metres by the litres in one cubic metre, read from the units table, and shows the result as the litres line.
Worked example: a low spot
Show the steps
- Area 5 m (16 ft 4 7/8 in) × 3 m (9 ft 10 1/8 in) = 15 m² (161.46 ft²)
- Volume in place, at the depth after compaction 15 m² (161.46 ft²) × 300 mm (11 13/16 in) (0.3 m) = 4.5 m³ (158.92 ft³)
- Loose volume: add the allowance 4.5 m³ (158.92 ft³) + 0% allowance = 4.5 m³ (158.92 ft³)
- Round up once, to the supplier's smallest order 4.5 m³ (158.92 ft³) = 4.5 m³ (158.92 ft³)
Assumptions
The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.
| Assumption | Value | Details and changes |
|---|---|---|
| Waste allowance | 0% | |
| Default No allowance unless you enter one. Check your label or supplier. | ||
| Allowance added to the in-place volume to give the loose volume | 0% | |
| Default No allowance unless you enter one. Check your label or supplier. | ||
| Supplier's smallest order, in cubic metres | 0.25 m³ (8.83 ft³, converted) | |
| Default Suppliers sell loose material in set amounts. This amount is a typed example: check your supplier. | ||
Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm
Loose volume at an allowance
The example low spot at three allowances
| Allowance | In place | Loose volume | Litres |
|---|---|---|---|
| 0 % | 4.5 m³ (158.92 ft³) | 4.5 m³ (158.92 ft³) | 4,500 L |
| 10 % | 4.5 m³ (158.92 ft³) | 4.95 m³ (174.81 ft³) | 4,950 L |
| 20 % | 4.5 m³ (158.92 ft³) | 5.4 m³ (190.7 ft³) | 5,400 L |
The calculator starts with no allowance. These three values only show how the input works: enter your own figure.
Common jobs
Soil in cubic metres and litres for common digging and filling jobs
| Job (size × depth) | Volume | Litres |
|---|---|---|
| Trench 12 m × 450 mm × 600 mm | 3.24 m³ (114.42 ft³) | 3,240 L |
| Level-up 4 m × 3 m × 100 mm | 1.2 m³ (42.38 ft³) | 1,200 L |
| Pit 2 m × 2 m × 1 m | 4 m³ (141.26 ft³) | 4,000 L |
Each row is worked out on its own, from the area and the depth, with no allowance. The sizes are examples to replace with your own.