Board and Batten Calculator

Enter a wall's width and height and the batten width, choose a set number of battens, a largest gap or a board width, and get every batten mark measured from the wall's left edge, with the stock pieces to buy.

Estimates for planning, not professional advice. Read the full notice.

Wall and battens

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 2.4 metres, 7 feet 10 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 2.4 metres, 7 feet 10 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 40 millimetres, 1 and 9 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 2.4 metres, 7 feet 10 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Example: a wall with five battens

5 battens

  • Gap between battens and at the ends 0.367 m (1.203 ft)
  • Centre to centre 0.407 m (1.334 ft)

Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.

  • Batten stock pieces, batten pieces, 40 mm × 2.4 m 5

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    What spacing do I use for board and batten?

    Take the batten widths off the wall and share what is left equally between the gaps. With a gap at each end there is one more gap than there are battens.

    How many battens do I need?

    Choose a set number, or give a largest gap or a board width and the calculator finds the fewest battens that keep every gap within it. Each batten is as long as the wall is high, less any rail.

    Worked example: a wall with five battens

    Show the steps
    1. Width the battens take 5 battens × 40 mm (1 9/16 in) = 200 mm (7 7/8 in)
    2. Wall left for gaps 2.4 m (7 ft 10 1/2 in) − 200 mm (7 7/8 in) = 2.2 m (7 ft 2 5/8 in)
    3. Gaps: one more than the battens, so the wall ends in a gap 2.2 m (7 ft 2 5/8 in) ÷ 6 gaps = 0.367 m (1.203 ft)
    4. Pieces: each batten is as long as the wall is high, cut from one stock piece 5 battens = 5 battens

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes
    Batten width 40 mm (1 9/16 in, converted)
    Default A typed example, not a maker's figure. Check the maker's sheet or your supplier and type your own.
    Stock piece length 2,400 mm (7 ft 10 1/2 in, converted)
    Default A typed example, not a maker's figure. Check the maker's sheet or your supplier and type your own.

    Furring and board stock, by maker

    Rows: 3

    The nominal sizes and the lengths each maker prints for its furring strips and boards, as printed

    The nominal sizes and the lengths each maker prints for its furring strips and boards, as printed
    ProductNominal size, inches (thickness by width)Length, feet
    Canfor Appearance Boards (Engelmann Spruce & Lodgepole Pine; trim and fine woodworking) 1x3 – 126 – 16
    Canfor Spruce Pine Fir furring strips 1x2 – 1x3, 2x2 – 2x3Up to 16
    Canfor WynnWood Paneling (tongue and groove, Premier / Classic) 1x4 – 86 – 16

    Figures in the Nominal size, inches (thickness by width) and Length, feet columns are per Canfor's product page, checked 15 Nov 2026.

    Product names are trademarks of their owners. HoneyDoMath is not affiliated with, sponsored by or endorsed by these makers. Figures come from each maker's published sheets and are shown for information only.

    Sources: [1][2][3]

    Canfor prints each size and length as a range; they are shown as printed, not worked out for your wall.

    Sources (3)

    1. Appearance Boards (Canfor product page) (opens in new tab), Canfor, Product page, undated. Manufacturer data.
      “Nominal Dimensions TxW, inches 1x3 – 12 Lengths Feet 6 – 16”
      Per Canfor's product page, checked 15 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 1)
    2. Furring strips (Canfor product page) (opens in new tab), Canfor, Product page, undated. Manufacturer data.
      “Nominal Dimensions TxW, inches 1x2 – 1x3, 2x2 – 2x3 Lengths Feet Up to 16”
      Per Canfor's product page, checked 15 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 2)
    3. WynnWood Paneling (Canfor product page) (opens in new tab), Canfor, Product page, undated. Manufacturer data.
      “Nominal Dimensions TxW, inches 1x4 – 8 Lengths Feet 6 – 16”
      “2x6 Tongue & Groove ... Nominal Dimensions Inches 2x6 Lengths Feet 12 – 20”
      Per Canfor's product page, checked 15 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 3)

    These are summaries of what the sources say, not professional advice. Building codes and product data change. Check with your local building department and the product label about your own project.