Even Spacing Calculator

Enter the length of a run and the width of each item, and choose a set number of items or a largest gap. The count of items placed is the live result; the equal gap, the centre-to-centre distance and every mark from the start of the run are worked out in the example and tables.

Estimates for planning, not professional advice. Read the full notice.

Run and items

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 1.8 metres, 5 feet 10 and 7 eighths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 90 millimetres, 3 and 9 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Example: five shelf brackets on a rail

5 items

  • Gap between items and at the ends 0.225 m (0.738 ft)
  • Centre to centre 0.315 m (1.033 ft)
  • First item, left edge 0.225 m (0.738 ft)
  • First item, centre 0.27 m (0.886 ft)

Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.

Gaps and marks

These numbers follow the sizes above for every item in the list. Every mark is measured from the start of the run.

  • Items to place, items placed 5

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    What is the difference between a gap at the ends and flush ends?

    With a gap at both ends the first and last items sit one gap in from the run's ends. Flush to both ends puts them against the ends, and flush at the start only puts the first against the start. The first table shows all three for one job.

    How do I space shelves or coat hooks evenly?

    Take the widths of the items off the length of the run and share what is left between the gaps. The example shows the math and the second table lists each mark from the start of the run.

    Worked example: five shelf brackets on a rail

    Show the steps
    1. Width the items take 5 items × 90 mm (3 9/16 in) = 0.45 m (1.476 ft)
    2. Run left for gaps 1.8 m (5 ft 10 7/8 in) − 0.45 m (1.476 ft) = 1.35 m (4.429 ft)
    3. Gap: one more gap than items, so the run ends in a gap 1.35 m (4.429 ft) ÷ 6 gaps = 0.225 m (0.738 ft)
    4. First centre: the gap plus half an item 0.225 m (0.738 ft) + 0.045 m (0.148 ft) = 0.27 m (0.886 ft)

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes

    The same job under the three end rules

    Gap, first centre and centre-to-centre distance for the example run under each end rule

    Gap, first centre and centre-to-centre distance for the example run under each end rule
    End ruleGapFirst centreCentre to centre
    Gaps at both ends 0.225 m (0.738 ft)0.27 m (0.886 ft)0.315 m (1.033 ft)
    Flush to both ends 0.338 m (1.107 ft)0.045 m (0.148 ft)0.427 m (1.403 ft)
    Flush at the start only 0.27 m (0.886 ft)0.045 m (0.148 ft)0.36 m (1.181 ft)

    Only the end rule changes. A gap at both ends has one more gap than items; flush to both ends has one fewer; flush at the start only has the same number.

    Marks for the example run

    Left edge, centre and right edge of each item, measured from the start of the example run

    Left edge, centre and right edge of each item, measured from the start of the example run
    ItemLeft edgeCentreRight edge
    Item 1 0.225 m (0.738 ft)0.27 m (0.886 ft)0.315 m (1.033 ft)
    Item 2 0.54 m (1.772 ft)0.585 m (1.919 ft)0.63 m (2.067 ft)
    Item 3 0.855 m (2.805 ft)0.9 m (2.953 ft)0.945 m (3.1 ft)
    Item 4 1.17 m (3.839 ft)1.215 m (3.986 ft)1.26 m (4.134 ft)
    Item 5 1.485 m (4.872 ft)1.53 m (5.02 ft)1.575 m (5.167 ft)

    Every mark is measured from the start of the run, never from the mark before it, so a slip does not carry along.