Stair Carpet Calculator

Enter a flight's total rise and run, or type the number of steps, to get the length of carpet for the treads and risers and the roll to buy in whole metres.

A ready-made setup of the Carpet Calculator.

Estimates for planning, not professional advice. Read the full notice.

Flight and carpet

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 2.7 metres, 8 feet 10 and 5 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 190 millimetres, 7 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 250 millimetres, 9 and 13 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 900 millimetres, 2 feet 11 and 7 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 4 metres, 13 feet 1 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Example: a straight flight

7 m of carpet

  • Risers 15 risers
  • Treads 14 treads
  • Riser height 0.18 m (7.087 in)
  • Length covered 6.2 m (20 ft 4 1/8 in)
  • Roll length with the waste 6.82 m (22 ft 4 1/2 in)

Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.

  • Carpet, by the linear metre, m of carpet 7

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    How much carpet do I need for 13 steps?

    Choose From a number of steps, pick 13 steps and type the riser height and run. Each stair takes its run plus its riser height. The stair width, waste allowance and roll width are examples until you change them.

    What is the length of carpet for one step?

    The run plus the riser height, plus any nosing wrap you add. The calculator adds the treads and the risers separately, so a flight whose top is the floor above has one tread fewer than risers.

    Worked example: a straight flight

    Show the steps
    1. Treads: the run times the treads 0.25 m (9.843 in) × 14 treads = 3.5 m (11 ft 5 13/16 in)
    2. Risers: the riser height times the risers 0.18 m (7.087 in) × 15 risers = 2.7 m (8 ft 10 5/16 in)
    3. Add the waste allowance, once 6.2 m (20 ft 4 1/8 in) × 1.1 = 6.82 m (22 ft 4 1/2 in)
    4. Round up once, to whole metres of roll 6.82 m (22 ft 4 1/2 in) = 7 m of carpet

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes
    Waste allowance 10%
    Default A typical allowance, added once to the length covered. Change it for your job.
    Stair width No default
    Default The width of the carpet on the stair. Check your label or supplier.
    Roll width No default
    Default Your roll's width, from your supplier; the figure shown is an example to start from. Check your label or supplier.
    Maximum riser height No default
    Default Your own target; the figure shown is an example, not a rule. Check your label or supplier.

    What one step takes

    The math for the example flight: a tread, a riser, one step and the whole flight

    The math for the example flight: a tread, a riser, one step and the whole flight
    PartLength
    Run 0.25 m (9.843 in)
    Riser height 0.18 m (7.087 in)
    One step 0.43 m (16.929 in)
    Treads and risers together 6.2 m (20 ft 4 1/8 in)
    With the waste allowance 6.82 m (22 ft 4 1/2 in)

    One step is its run plus its riser height, with any nosing wrap you add. The flight is its treads and risers added, then the waste allowance once.