Roofing Underlayment Calculator

Enter the roof footprint and pitch in degrees and the width, length and laps of your roll, and get the rolls of roofing underlayment for the whole roof, with waste added once and rounded up once. The laps are numbers you enter.

Estimates for planning, not professional advice. Read the full notice.

Roof and roll

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 10 metres, 32 feet 9 and 11 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 8 metres, 26 feet 2 and 15 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 1 metre, 3 feet 3 and 3 eighths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 50 metres, 164 feet 1 half of an inch

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 100 millimetres, 3 and 15 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 150 millimetres, 5 and 7 eighths inches

Example: a gable roof under underlayment

3 rolls of roofing underlayment

  • Roof area 92.38 m² (994.33 ft²)
  • Area one roll covers after the laps 44.87 m² (482.92 ft²)

Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.

  • Roofing underlayment rolls, Roofing underlayment roll, 1 m by 50 m 3

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    How many rolls of roofing underlayment do I need?

    The roof area is the footprint times the pitch multiplier. Each roll covers its width less the side lap times its length less the end lap. The area plus waste over that, rounded up once, is the rolls.

    Where do the laps come from?

    Your roll's label or your supplier. The calculator uses the laps you type and shows the area one roll covers after them.

    Worked example: a gable roof under underlayment

    Show the steps
    1. Footprint: length times width 10 m (32 ft 9 11/16 in) × 8 m (26 ft 2 15/16 in) = 80 m² (861.11 ft²)
    2. Roof area: footprint times the pitch multiplier 80 m² (861.11 ft²) × 1.1547 = 92.38 m² (994.33 ft²)
    3. One roll after the laps: width less the side lap, times length less the end lap 900 mm (2 ft 11 7/16 in) × 49.85 m (163 ft 6 5/8 in) = 44.87 m² (482.92 ft²)
    4. Rolls: roof area plus waste, over what one roll covers, rounded up once 92.38 m² (994.33 ft²) + 10% waste ÷ 44.87 m² (482.92 ft²) = 3 rolls of roofing underlayment

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes
    Waste allowance 10%
    Default Your own allowance, added once to the total. Check your label or supplier.

    What NBC 2020 prints for eave protection

    Eave protection on shingle, shake or tile roofs, Sentence 9.26.5.1.(1) of the National Building Code of Canada 2020

    Eave protection on shingle, shake or tile roofs, Sentence 9.26.5.1.(1) of the National Building Code of Canada 2020
    FigureValue in the code
    Up the roof slope from the edge of the roof, at least 900 mm (2 ft 11 7/16 in, converted)
    Inside the inner face of the exterior wall, at least 300 mm (11 13/16 in, converted)

    Source: [1]

    The code lists exceptions to this sentence, and provinces and territories adopt it with changes: your local building department decides what applies to your roof.

    Underlay and ice barrier rolls by maker

    Rows: 1

    The width, the length and the area of one roll, as each maker prints them

    The width, the length and the area of one roll, as each maker prints them
    ProductRoll widthRoll lengthRoll area
    IKO StormShield Ice & Water Protector 914.4 mm (36 in, as published)19.812 m (65 ft, as published)18.12 m² (195 ft², as published)

    Figures in the Roll width, Roll length and Roll area columns are per IKO's data sheet, checked 14 Nov 2026.

    Product names are trademarks of their owners. HoneyDoMath is not affiliated with, sponsored by or endorsed by these makers. Figures come from each maker's published sheets and are shown for information only.

    Source: [2]

    Every figure is the maker's printed figure for one roll.

    Sources (2)

    1. National Building Code of Canada 2020, Sentence 9.26.5.1.(1) (opens in new tab), National Research Council of Canada, NBC 2020, Division B (Volume 2), NRC printing with revisions and errata of 31 March 2025. Code or government.
      “eave protection shall be provided on shingle, shake or tile roofs, extending from the edge of the roof a minimum of 900 mm up the roof slope to a line not less than 300 mm inside the inner face of the exterior wall.”
      Checked 13 November 2026. Figures and codes change; verify with the source. Back to where this is used (Source 1)
    2. StormShield Ice & Water Protector, technical data sheet (12/2025) (opens in new tab), IKO Industries Ltd., Technical data sheet, 12/2025. Manufacturer data.
      “195 ft.2 (18.1 m2)”
      “Rolls/Pallet 44”
      “36 in. (914 mm)”
      “65 ft. (19.8 m)”
      “Thickness 43 mils (1.08 mm)”
      Per IKO's data sheet, checked 14 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 2)

    These are summaries of what the sources say, not professional advice. Building codes and product data change. Check with your local building department and the product label about your own project.