Stairs With Landing Calculator

Enter the total rise, your maximum riser height, the run and the landing size to get the risers, treads, run and stringer length of each flight and the height of the landing. The stairs with a landing calculator makes no regulation claim.

A ready-made setup of the Stair Calculator.

Estimates for planning, not professional advice. Read the full notice.

Stair and landing

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 2.7 metres, 8 feet 10 and 5 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 190 millimetres, 7 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 250 millimetres, 9 and 13 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 900 millimetres, 2 feet 11 and 7 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 900 millimetres, 2 feet 11 and 7 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 25 millimetres, 1 inch

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

Example: a stair with a landing

4 stair stringers

  • Risers in the whole stair 15 risers
  • Riser height 0.18 m (7.087 in)
  • Risers below the landing 7 risers
  • Risers above the landing 8 risers
  • Landing height 1.26 m (4 ft 1 5/8 in)

Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.

  • Stair stringer, 2.4 m, stair stringers, 2.4 m 4

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    How are the risers split between the two flights?

    The whole stair has the fewest risers that keep each riser at or under your maximum riser height, and every riser is the total rise over that count. By default half the risers go below the landing; choose a number of risers below the landing to move it.

    Why does each flight have one tread fewer than risers?

    The landing is a tread level, so the lower flight ends on it, and the upper flight ends at the floor above on a standard mount. A flush mount puts the top tread on the stringer.

    Worked example: a stair with a landing

    Show the steps
    1. Risers of the whole stair: the total rise over the maximum riser height, rounded up 2.7 m (8 ft 10 5/16 in) ÷ 0.19 m (7.48 in) = 15 risers
    2. Riser height: the total rise over those risers 2.7 m (8 ft 10 5/16 in) ÷ 15 risers = 0.18 m (7.087 in)
    3. Landing height: the risers below it times the riser height 7 risers × 0.18 m (7.087 in) = 1.26 m (4 ft 1 5/8 in)
    4. Run: each flight's treads times the run, plus the landing depth 13 treads × 0.25 m (9.843 in) + 0.9 m (35.433 in) = 4.15 m (13 ft 7 3/8 in)

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes
    Maximum riser height 190 mm (7 1/2 in, converted)
    Default Your own target; the figure shown is an example, not a rule. Check your label or supplier.
    Run No default
    Default The depth of a tread. Check your label or supplier.
    Landing depth and width No default
    Default Your own landing size. Check your label or supplier.
    Stringer lengths No default
    Default The board lengths you can buy. Check your label or supplier.

    Each flight, figure by figure

    Risers, riser height, treads, run and stringer length for the lower and upper flight of the example stair

    Risers, riser height, treads, run and stringer length for the lower and upper flight of the example stair
    FigureLower flightUpper flight
    Risers 78
    Riser height 0.18 m (7.087 in)0.18 m (7.087 in)
    Treads 67
    Run of the flight 1.5 m (4 ft 11 1/16 in)1.75 m (5 ft 8 7/8 in)
    Stringer length with the cut allowance 1.848 m (6 ft 3/4 in)2.156 m (7 ft 7/8 in)

    Every riser is the total rise over the risers of the whole stair. The landing is a tread level, so each flight has one tread fewer than its risers. The stringer length is geometry only; no board is sized.