Plywood Calculator

Enter a floor, a wall or a typed area and pick a sheet size to get the sheets of plywood or any panel, by area or by laying out rows, rounded up once.

Estimates for planning, not professional advice. Read the full notice.

Floor, wall or area

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 4.8 metres, 15 feet 9 inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 3.6 metres, 11 feet 9 and 3 quarters inches

Example: a floor of plywood sheets

7 sheets

  • Area of the floor 17.28 m² (186 ft²)
  • Sheets with no waste 5.81 sheets
  • Sheets with the waste, before rounding 6.4 sheets
  • Rows of sheets across the floor 2.95 rows
  • Sheets counted by layout, no waste 6 sheets
  • Plywood sheets, Plywood or panel sheet, 2438 × 1219 mm 7

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    How many sheets of plywood do I need for a floor?

    Enter the floor's length and width and choose the sheet size. The calculator divides the floor area, plus your waste allowance, by the area of one sheet and rounds up once. A floor that is exactly a whole number of sheets is that whole number until waste is added.

    Can I use it for roof sheathing?

    Type the roof's area with Draw a shape, or work it out first, and the area method counts the sheets for that area. The calculator counts sheets only and gives no spans or fasteners.

    Is the count the same for OSB?

    Yes. The count depends on the area and the size of the sheet, so the same sheets of OSB or any other panel of the same size come to the same number.

    What is the difference between counting by area and by layout?

    Area divides the total area by one sheet. Layout lays rows of sheets across the shorter side and cuts each row from sheets of the chosen length, so it never gives fewer sheets than the area count. The calculator orders the larger of the two.

    Worked example: a floor of plywood sheets

    Show the steps
    1. Area: length times width 4.8 m (15 ft 9 in) × 3.6 m (11 ft 9 3/4 in) = 17.28 m² (186 ft²)
    2. Add the waste allowance, once 17.28 m² (186 ft²) + 10% = 19.01 m² (204.6 ft²)
    3. Divide by the area of one sheet 19.01 m² (204.6 ft²) ÷ 2.97 m² (31.99 ft²) = 6.4 sheets
    4. Round up once, to whole sheets 6.4 sheets = 7 sheets

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes
    Waste allowance 10%
    Default An example allowance for cuts and breakage, added once. Change it for your own job.
    Sheet size No default
    Default The starting size is the one the maker prints, cited on this page. Choose the size your supplier sells from the list above the result.
    Sheet size, length 2.438 m (8 ft, as published)[1]
    West Fraser's Trubord page lists a size of 4x8 (feet) and thicknesses of 3/8 to 23/32 (inches); it prints no metric size.
    Sheet size, width 1.219 m (4 ft, as published)[1]
    West Fraser's Trubord page lists a size of 4x8 (feet) and thicknesses of 3/8 to 23/32 (inches); it prints no metric size.

    Sources (1)

    1. Trubord roof and wall sheathing (West Fraser product page) (opens in new tab), West Fraser, Product page, undated. Manufacturer data.
      “Sizes / Lengths: 4x8”
      “Thickness: 3/8 - 23/32”
      Per West Fraser's product page, checked 13 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 1)

    These are summaries of what the sources say, not professional advice. Building codes and product data change. Check with your local building department and the product label about your own project.