Metal Roof Sheet Calculator

Enter the eaves length, the run of a plane, the pitch in degrees, the sheet cover width and the stock length and get the metal roof sheets by column and cut length for a gable or shed roof, with ridge and trim pieces, each rounded up once. A hip roof is not counted.

Estimates for planning, not professional advice. Read the full notice.

Roof plane and sheets

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 10 metres, 32 feet 9 and 11 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 50 millimetres, 1 and 15 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 4 metres, 13 feet 1 and 1 half inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 100 millimetres, 3 and 15 sixteenths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 1 metre, 3 feet 3 and 3 eighths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 6 metres, 19 feet 8 and 1 quarter inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 150 millimetres, 5 and 7 eighths inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 3 metres, 9 feet 10 and 1 eighth inches

Example: a gable roof in metal sheets

22 metal roof sheets

  • Columns on each plane 11 columns
  • Cut length of one sheet 4.719 m (15 ft 5 3/4 in)
  • Ridge pieces 4 ridge pieces

Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.

  • Metal roof sheets, Metal roof sheets, 1 m cover, 6 m long 22
  • Ridge pieces, Ridge pieces, 3 m 4
  • Eaves trim, Eaves trim pieces, 3 m 7
  • Rake trim, Rake trim pieces, 3 m 7

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    How many metal roof sheets do I need?

    The calculator counts columns across each plane from the eaves length and the cover width, finds the cut length of a sheet from the run and the pitch, and cuts each column from stock. It counts by column and length, never by area.

    How long is a metal roof sheet?

    The run times the pitch multiplier, plus the eaves overhang measured along the slope.

    Worked example: a gable roof in metal sheets

    Show the steps
    1. Columns: the eaves length plus the rake overhang at both ends, over the cover width, rounded up 10.1 m (33 ft 1 5/8 in) ÷ 1 m (3 ft 3 3/8 in) = 11 columns
    2. Cut length: the run times the pitch multiplier, plus the eaves overhang 4 m (13 ft 1 1/2 in) × 1.1547 + 100 mm (3 15/16 in) = 4.719 m (15 ft 5 3/4 in)
    3. Sheets: the columns on each plane, cut from stock, times the planes 11 columns × 2 planes = 22 metal roof sheets

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes

    Metal roof panels by maker

    Rows: 1

    The lowest roof pitch a maker prints for its panel

    The lowest roof pitch a maker prints for its panel
    ProductLowest roof pitch printed
    Vicwest Tradition 100 (steel roof panel, hidden fasteners) 3 in 12

    Figures in the Lowest roof pitch printed column are per Vicwest's product page, checked 15 Nov 2026.

    Product names are trademarks of their owners. HoneyDoMath is not affiliated with, sponsored by or endorsed by these makers. Figures come from each maker's published sheets and are shown for information only.

    Source: [1]

    The pitch is shown as the maker prints it, as a rise over twelve.

    Sources (1)

    1. Tradition 100 (Vicwest product page) (opens in new tab), Vicwest, Product page, undated. Manufacturer data.
      “Ideal for sloped roofs as low as 3 in 12”
      Per Vicwest's product page, checked 15 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 1)

    These are summaries of what the sources say, not professional advice. Building codes and product data change. Check with your local building department and the product label about your own project.