Deck Stain Calculator

Enter the length and width of the deck, the coats and the area one litre covers from your can, and get the litres of deck stain, rounded up once to whole cans of the size you buy. The coverage options are the figures a maker prints for its stain; your can gives its own figure.

Estimates for planning, not professional advice. Read the full notice.

Surface to stain

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 4.8 metres, 15 feet 9 inches

Metres, centimetres or millimetres, like 3.8 m, 10 cm or 250 mm

reads as 3.6 metres, 11 feet 9 and 3 quarters inches

Example: a deck top

2 3.78 L cans

  • Stain needed, in litres, before rounding to cans 4.69 L

Estimate for planning, from what you entered and the product data shown. Check product labels and your supplier before you buy.

  • Deck stain, 3.78 L can 2

Share this project

This link carries:

    The project is inside the link, after the # sign. Browsers do not send that part to the site.

    Questions

    How much deck stain do I need?

    Multiply the area by the coats and divide by the coverage of one litre on your can, then round up to whole cans. The example shows each step with example figures; your can gives the real coverage.

    Why does the coverage change so much?

    Coverage depends on the stain and on the wood, and rough or weathered boards take more. That is why the calculator asks for a coverage from your own can instead of assuming one.

    Worked example: a deck top

    Show the steps
    1. Area of the deck top 4.8 m (15 ft 9 in) × 3.6 m (11 ft 9 3/4 in) = 17.28 m² (186 ft²)
    2. Litres: the area times the coats, over the coverage of one litre 17.28 m² (186 ft²) × 2 coats ÷ 7 m² (79 ft²) = 4.69 L
    3. Round up once, to whole cans 4.69 L = 2 × 3.78 L cans

    Assumptions

    The figures behind the example. Sourced figures link to their source below; a default is a starting value to check against your label or supplier.

    AssumptionValueDetails and changes
    Coverage of one litre (use your own can's figure) 27.9 sq. m. per gallon[1]
    Benjamin Moore Canada's Woodluxe Oil-Based Semi-Transparent stain page prints a coverage of 27.9 to 37.2 sq. m. (300 to 400 sq. ft.) per gallon.

    Litres of stain by deck size and coverage

    Litres of stain for the top of a deck at two coats, by deck size and by the coverage of one litre, with the cans at the middle coverage

    Litres of stain for the top of a deck at two coats, by deck size and by the coverage of one litre, with the cans at the middle coverage
    Deck topLitres at the first coverageLitres at the middle coverageLitres at the last coverageCans at the middle coverage
    3 × 3 m 2.25 L1.8 L1.5 L1 × 3.78 L can
    3.6 × 4.8 m 4.32 L3.46 L2.88 L1 × 3.78 L can
    4 × 6 m 6 L4.8 L4 L2 × 3.78 L cans
    5 × 6 m 7.5 L6 L5 L2 × 3.78 L cans
    6 × 8 m 12 L9.6 L8 L3 × 3.78 L cans

    The coverages are examples. The litres are exact; the cans are rounded up once. Your own can gives its own coverage.

    Coverage per can, as Sico prints it

    Rows: 2

    Can size and coverage per coat of the Sico stains, as the maker prints them

    Can size and coverage per coat of the Sico stains, as the maker prints them
    ProductCan sizeCoverage per coat, fromCoverage per coat, to
    SICO 134-XXX exterior semi-transparent stain for wood (water-based) 3.78 L45 m² (484.38 ft², converted)52 m² (559.72 ft², converted)
    SICO 236-X80 exterior wood finish (semi-transparent, solvent) 3.78 L56 m² (602.78 ft², converted)65 m² (699.65 ft², converted)

    Figures in the Can size, Coverage per coat, from and Coverage per coat, to columns are per Sico's data sheet, checked 14 Nov 2026.

    Product names are trademarks of their owners. HoneyDoMath is not affiliated with, sponsored by or endorsed by these makers. Figures come from each maker's published sheets and are shown for information only.

    Sources: [2][3]

    Sico prints the coverage of one can per coat as two figures; the table shows both ends.

    Sources (3)

    1. Woodluxe Oil-Based Waterproofing Exterior Stain + Sealer, Semi-Transparent, 3.78 L (Benjamin Moore Canada product page) (opens in new tab), Benjamin Moore & Co., Product page, undated. Manufacturer data.
      “Coverage (Sq. Ft./Gal) 200-400 27.9 – 37.2 sq. m. (300 – 400 sq. ft.) 27.9 – 37.2 sq. m. (300 – 400 sq. ft.)”
      Per Benjamin Moore's product page, checked 14 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 1)
    2. SICO 134-XXX exterior semi-transparent stain, technical data sheet (opens in new tab), PPG Architectural Coatings Canada (Sico), Technical data sheet, edition not printed in the text read. Manufacturer data.
      “3.78 L: 45 to 52 m2 (480 to 560 ft2)”
      Per Sico's data sheet, checked 14 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 2)
    3. SICO 236-X80 exterior wood finish, technical data sheet (opens in new tab), PPG Architectural Coatings Canada (Sico), Technical data sheet, edition not printed in the text read. Manufacturer data.
      “3.78 L: 56 to 65 m2 (600 to 700 ft2)”
      Per Sico's data sheet, checked 14 Nov 2026. Figures and codes change; verify with the source. Back to where this is used (Source 3)

    These are summaries of what the sources say, not professional advice. Building codes and product data change. Check with your local building department and the product label about your own project.